logo
Electronic Universal Testing Machines - Model : UTES (Servo)
Request a Quote

Electronic Universal Testing Machines - Model : UTE

Features

  • Motorised Control Valve.
  • Load accuracy as high + 1%.
  • Straining at variable speeds to suit a wide range of materials.
  • Printer & PC graphs enable study the behavior of the material.
  • Motor driven threaded columns for quick effortless adjustment of middle crosshead to facilitate rapid fixing of test specimen.
  • Simplicity in reading because of digital readouts.
  • Wide range of standard and special accessories.
  • Easy change from plain to threaded and screwed specimens.
  • Large effective clearance between columns enable testing of standard specimens as well structures.
  • Simple controls for ease of operation.
  • Robust straining frame of an extremely rigid construction.
  • Fully enclosed and protected pressure transducer.
  • RS 232 serial port for PC control of m/c.
FIE Electronic Universal Testing Machine is designed for testing metals and other materials under tension, compression bending, transverse and shear loads. Hardness test on metals can also conducted.

Here UTM Right Control Valve is Servo Controlled in close loop mode as per mode selection. Following control modes available :

  • Standard Manual Control
  • Potentiometric Control
  • Load Rate Control
  • Elongation Rate Control
  • Load Hold Mode
  • Strain Rate Control
  • Also Auto Start, Potentiometric start & Initial Valve open start options are available for test to take care of slippage & different specimen types.
    Load is applied by hydrostatically lubricated ram. Main cylinder pressure is transmitted to the pressure transducer housed in the control panel. The transducer gives the signal to the electronic display unit, corresponding to the load exerted by the main ram. Simulteniously the digital encoder fitted on the straining unit gives the mechanical displacement.

This consists of a cylinder motor with chain and sprocket drive and a table coupled with the ram of the hydraulic cylinder, mounted on to a robust base. The cylinder and the ram are individually lapped to eliminate friction. The upper cross-head is rigidly fixed to the table by two strenthened columns.
The lower cross-head is connected to two screwed columns which are driven by a motor. Axial loading of the ram is ensured by relieving the cylinder and ram of any possible side loading by the provision of ball seating.
An displacement scale with a minimum graduation of 1mm, is provided to measure the deformation of the specimen.
Tension test is conducted by gripping the test specimen between the upper and lower cross-heads.
Compression, transverse , bending, shear & hardness tests are conducted between the lower cross-head and the table.
The lower cross-head can be raised or lowered rapidly by operating the screwed columns, thus facilitating ease of fixing of the test specimen.

The control Panel consists of a power pack complete with drive motor and an oil tank, control valves and electronic display unit.

The power pack generates the maximum pressure of 200 kgf/cm2. The hydraulic pump provides continuously non-pulsating oil flow. Hence the load application is very smooth.

Hand operated Release Valve & motorised control valve are used to control the flow to and from the hydraulic cylinder. The regulation of the oil flow is infinitely variable. Incorporated in the hydraulic system is a regulating valve, which maintains a practically constant rate of piston movement. Control by this valve allows extensometer reading to be taken.

  • Electronic panel 8085 microprocessor is used for basic UTM operation & an 8 bit dedicated microcontroller is used for close loop & Servo Control.
  • Panel is having parallel printer port, RS 232 C serial port for PC interface.
  • 2 lines x 8 digits 7 segment display & membrane keyboard for data entry.
  • 20 data sets and 50 results storage.

Windows based basic software for Servo Control is in standard scope of supply.

  • Real Time graph, User friendly software.
  • Extensive graphics on screen for curve plotting, magnification and zooming.
  • Extensive graphics on screen for curve plotting, magnification and zooming.
  • Extensive graphics on screen for curve plotting, magnification and zooming.
  • Statistical evaluation with water fall dig., Mean deviation, frequency distribution, Skew dig., Histogram. Also calculates max. value, min.value, Mean Value, Variance, Standard Deviation. (Other statistical parameters on request). Selectable batch & statistical printouts.
  • Evaluation of wide range of user selectable parameters such as % elongation, % reduction in area, young's modulus, yield stress, proof stress etc.
  • Optional Software packages for Extensometer, Shear Bend, Torsion, Rubber, Textile testing etc.

All FIE Electronic Universal Testing Machines are closely controlled for sensitivity, accuracy and calibration during every stage of manufacture. Every machine is then calibrated over each of its measuring ranges in accordance with the procedure laid down in British standards.1610 : Part 1 : 1992 and IS : 1828 : Part 1 : 1991.

Fie Electronic Universal Testing Machine comply with Grade "A" of BS : 1610 : Part 1 : 1992 and class 1 of IS - 1828-Part 1:1991. An accuracy of + 1% is guaranted from 2% to 100% of the capacity of the machine.

Below 20% of the selected range , the maximum permissible error is 0.2% of the full load reading.

Model Units UTES-10 UTES-20 UTES-40 UTES-60 UTES-100
Maximum Capacity kN 100 200 400 600 1000
Measuring Range kN 0-100 0-200 0-400 0-600 0-1000
Load Resolution (20,000 counts full scale) N 5 10 20 30 50
Load Range with Accuracy of measurement ± 1.0% kN 2 to100 4 to 200 8 to 400 12 to 600 20 to 1000
Resolution of piston movement (Displacement) mm 0.01 0.01 0.01 0.01 0.01
Clearance for tensile at fully descended working piston. mm 50-700 50-700 50-700 50-800 50-850
Clearance for compression test at fully descended working piston. mm 0-700 0-700 0-700 0-800 0-850
Clearance between columns. mm 500 500 500 600 750
Ram Stroke mm 150 200 200 250 250
Straining/piston speed (at no load) mm/min 0-300 0-150 0-150 0-100 0-80
Connected Load
Power kW 1.0 1.0 1.7 1.9 2.6
Voltage
V ac
400-440 400-440 400-440 400-440 400-440
Phase(Ø) 3 3 3 3 3
Dimensions
L x W x H ( approx. ) mm 2032 x
750 x
1960 x
2032 x
750 x
1960 x
2060 x
750 x
2180 x
2265 x
750 x
2534 x
2415 x
815 x
2900 x
Weight (approx.) kg. 1500 1500 2500 3500 5500
Standard Accessories
For Tension Test
• Clamping jaws for round specimens of Diameters. mm 10-20
20-30
10-20
20-30
10-25
25-40
10-25
25-40
40-55
10-25
25-45
45-70
• Clamping jaws for flat specimens of thickness. mm 0 - 10
10 - 20
0 - 10
10 - 20
0 - 15
15 - 30
0 - 15
15 - 30
0 - 22
22 - 44
44 - 65
Width mm 50 50 65 70 70
For Compression Test
Pair of compression plates of dia. mm 120 120 120 120 160
For Transverse Test
Table with adjustable rollers width of rollers. mm 160 160 160 160 160
Diameter of Rollers mm 30 30 30 50 50
Maximum clearance between supports mm 500 500 500 600 800
Radius of punch tops. mm 6, 12 6, 12 12, 16 16, 22 16, 22
  • Electronic Extensometer
  • Brinell Test Attachment
  • Printer
  • Shear Test Attachment
  • Software Packages
  • Wide range accessories offered on request at additional cost.
  • Due to constant R& D specifications & features are subjest to change without notice.
  • The dimensions given above are approximate.

Attachment for Tension Test for shouldered and threaded specimens

Tension Test

Universal 2001-UTE

Attachment for Tension Test for Wire Ropes

Compression Test

Products